my profile | my password | search | faq & rules | forum home

» Film-Tech Forum ARCHIVE   » Operations   » Digital Cinema Forum   » Setup for Barco ICMP and USL JSD-80 (Page 2)

This topic comprises 2 pages: 1  2

Author Topic: Setup for Barco ICMP and USL JSD-80 Wang Lance Film Handler Posts: 9 From: Taichung City, Taiwan Registered: Feb 2019 posted 02-22-2019 10:35 PM                     quote: Harold Hallikainen Early firmware did not support ping, so it's possible that it does not respond to ping. That could indeed be the reason of failed connection. Thanks Harold for the hint. I also tried Tera Term and the commands worked fine. quote: Steve Guttag the USB connector does NOT protrude from the front panel OK my bad, the USB connector is there. Thanks Steve.  |  IP: Logged Carsten Kurz Film God Posts: 4340 From: Cologne, NRW, Germany Registered: Aug 2009 posted 02-23-2019 06:23 AM                     If it works with Teraterm, there is no reason it shouldn't work from the Barco. I will just take some time to fiddle around with the command strings and parameters. You could also try sending the same string from the Barco to Teraterm and see wether and how it comes out there. - Carsten  |  IP: Logged Wang Lance Film Handler Posts: 9 From: Taichung City, Taiwan Registered: Feb 2019 posted 02-23-2019 09:48 AM                     quote: Carsten Kurz You could also try sending the same string from the Barco to Teraterm and see wether and how it comes out there. That is something I must try. Thanks Carsten.  |  IP: Logged Stephan Shelley Jedi Master Film Handler Posts: 854 From: castro valley, CA, usa Registered: Nov 2014 posted 02-23-2019 12:43 PM                     I would double check your device settings as well. Make sure you have the right address and port. I expect you are going through the projector LAN port for the commands and not one of the ports on the ICMP. Make sure the projector is on the same network as the JSD-80.  |  IP: Logged Wang Lance Film Handler Posts: 9 From: Taichung City, Taiwan Registered: Feb 2019 posted 02-25-2019 08:59 AM                     Hi Stephen, The setting for IP address and port (10,001) has been checked by different people to make sure it is correct. And yes I am going through the projector LAN port for the commands instead of the ones on the ICMP. I can use laptop to access both projector and JSD-80 using the IP addresses on the same network.  |  IP: Logged Harold Hallikainen Jedi Master Film Handler Posts: 906 From: Denver, CO, USA Registered: Aug 2009 posted 02-25-2019 09:08 AM                        Can you insert an Ethernet hub and run Wire Shark to see what's passing between the Barco and the JSD? Harold  |  IP: Logged Carsten Kurz Film God Posts: 4340 From: Cologne, NRW, Germany Registered: Aug 2009 posted 02-25-2019 10:51 AM                     Can you still buy hubs? I know I have two 100MBit hubs in my equipment storage, but these are more than 15 years old. I know some more expensive managed switches can copy traffic to ports for monitoring, though. I also guess I have one or two small 10MBit hubs lying around somewhere, ready to be dumped, but I notice that many ethernet ports nowadays do not support 10MBit/s anymore. - Carsten  |  IP: Logged Bruce Cloutier Expert Film Handler Posts: 161 From: Gibsonia, PA, USA Registered: Aug 2016 posted 02-25-2019 11:11 AM                        The Netgear Dual Speed Hubs are still around and on Amazon for instance. I would suggest grabbing one and keeping one around for this diagnostics use. I actually bought several for INTEG recently just to make sure that we have them around for Wireshark. That was part of the rationale for adding the network capture (compatible with Wireshark) to the JNIOR (Series 4). All of the PHY chips still support 10MBit/s in auto-negotiation. So I wonder if those Ethernet ports really wouldn't handle it? It is just maybe not worth advertising anymore.  |  IP: Logged Carsten Kurz Film God Posts: 4340 From: Cologne, NRW, Germany Registered: Aug 2009 posted 02-25-2019 11:27 AM                     Yeah, maybe, I may have just read specs which omitted the '10'. - Carsten  |  IP: Logged Wang Lance Film Handler Posts: 9 From: Taichung City, Taiwan Registered: Feb 2019 posted 02-26-2019 07:19 AM                     quote: Harold Hallikainen Can you insert an Ethernet hub and run Wire Shark to see what's passing between the Barco and the JSD? Thanks Harold. That's a good point for debugging. Hopefully I will be able to come back with good news after checking the firmware/ network status.  |  IP: Logged Marin Zorica Jedi Master Film Handler Posts: 671 From: Biograd na Moru, Croatia Registered: May 2003 posted 11-05-2019 01:49 PM                     I just did play with one DST XD10P on service which i got to have as spare when costumer has dead processor. It has all that needs for backup. Anyway, i was also testing RS232 automation, so did add small arduino to pass me commands from ethernet to RS232, but that is another thing...... I see on last tread there was no solution to get it work with Barco ICMP, maybe because it reads numbers as hex, so, when you send level 46, barco icmp send you ASCII, not hex as I am aware? So, maybe it should work like: level 0x46\0x0D Same thing is when i using RealTerm and if i chose to send mixed ascii and hex numbers i must use that way.......and it works.  |  IP: Logged Harold Hallikainen Jedi Master Film Handler Posts: 906 From: Denver, CO, USA Registered: Aug 2009 posted 11-05-2019 03:29 PM                        JSD-80 commands are at http://ftp.uslinc.com/Products/JSD-80/Documents/Technical/Jsd80AutomationCommands.pdf . Note also that the JSD-80 UART has only an 8 byte FIFO, so it's possible to miss characters if they are sent too fast or if hardware handshake is not used. Details at http://ftp.uslinc.com/Products/JSD-80/Documents/Technical/jsd80handshake.pdf . Harold  |  IP: Logged

All times are Central (GMT -6:00)

This topic comprises 2 pages: 1  2

Printer-friendly view of this topic

Hop To: Select a Forum: Category: Operations -------------------- Digital Cinema Forum Film Handlers' Forum Large Format Forum Ground Level Feature Info, Trailer Attachments & REAL Credit Offsets Category: Community -------------------- Film-Yak Film Handlers' Movie Reviews The Afterlife Bob Maar's Joke-A-Thon Category: Classified -------------------- Equipment and Supplies Wanted/For Sale Help Wanted/Seeking Employment Category: System -------------------- Software Beta Testing Forum

The Film-Tech Forums are designed for various members related to the cinema industry to express their opinions, viewpoints and testimonials on various products, services and events based upon speculation, personal knowledge and factual information through use, therefore all views represented here allow no liability upon the publishers of this web site and the owners of said views assume no liability for any ill will resulting from these postings. The posts made here are for educational as well as entertainment purposes and as such anyone viewing this portion of the website must accept these views as statements of the author of that opinion and agrees to release the authors from any and all liability.