There are "frequency", "Cut" and "Q setting".
Can someone explain me in simple words?
Thanks, in advance!
------------------
Antonio Marcheselli
Projectionist of Cinema Vittoria
Florence, Italy
What I'd like to know is why the CP500 is incapable of having it's optical subwoofer level reach spec? There is plenty of gain for the digital sub, but never enough for optical.
... ehm... perhaps not so simple!!!
Antonio
Frequency: dials in the particular frequency that will be boosted or cut (to determine the exact frequency being equalized requires a spectrum analyzer)
Cut: Once a desired frequency is selected via the 'frequency' control, the Cut control will raise or lower (boost or cut) the level of that frequency.
Q: I am not absolutely certain but I believe the "Q" controls the resonance of that particular frequency or the resonance of the equalizer/filter (?)
Hope this is a little more simple and undertandable.
Aaron
This process usually involves quite a bit of cussing the first few times you use a parametric equalizer.
I hope to be "really, really good at it" someday *grin*!
Russ
After you get used to it, I think a parametric EQ is a lot better than a graphic EQ. Unless you have a really good ear, it's hard to know which band on a graphic EQ to change. With a parametric, you can "zoom in" on the range you want to cut.
Ok, using a RTA makes it a whole lot better but when you gotta' do it by ear that's what I'd prefer.
Brad, you're right, perhaps "simple" wasn't the right word, sorry!!
Antonio
"Another question: How can I determine the "frequency" with a spectrum analyzer?"
If you turn the Cut control for maximum boost, the frequency that the 'frequency' control is set for should spike up on the RTA display.
If the sub is properly equalized the RTA display should be pretty much 'flat' across the low end of the spectrum with no peaks...
Aaron
So to EQ a Subwoofer I should:
1. Set the "Cut" to maximum
2. Searching the frequency for what the RTA response is better and set it
3. Set "cut" and "Q" to a value that make the response as flat as possible
Right?
What happen if the same subwoofer in the same theater is set once to 60Hz and once to 33Hz?
It works bettere around 60Hz first time and 33Hz the other?
Or one of the setting is wrong since the "frequency" is a feature of the Subwoofer's type?
Bye!
Get a copy of the CP500 or CP65 installation and alignment manuals and follow the instructions to the letter using an RTA and microphone(s) in the auditorium.
I am not exactly sure what you are meaning with the subwoofer being set for 33 and 60 Hz. Properly equalized, the sub should be fairly flat from close to DC to about 100 Hz.
Aaron
The CP-500's (as are all Dolby subwoofer eqs) is a single band parametric equalizer. Since their goal is to "kill" any resonant peaks caused by the subwoofer and room interaction, the "cut" means just that it is cut only. Therefore when set to max, the equalizer is set to flat, regardless of where the other two settings are (Q and frequency).
How to set the eq:
Look on your analyzer and see if you have any peeks in the pass band of your sub (different subs handle different ranges, particularly if B-6 tuned subs are used). If you don't have any pronounced peaks, then leave it alone (just like the stage channels, if they come up within spec, you don't adjust willy-nilly)
How easy it is to adjust partially depends on your analyzer. I find most LED based analyzers have too slow ballistics to allow easy adjustment. My favorite analyzer is the Abacus ARTA-800, it is a scope attactment and the resulting display lets one see the affects of the parametric EQ very plainly and quickly.
Anyway, what you want to do first is turn the "Q" to maximum. This will limit the bandwith of the equalizer. Then turn the "Cut" to minimum. This should put a finger down at the frequency selected. I start at the lowest frequency available and start raising the frequency until I see the "finger" move up until the "finger" is centered on the frequency where the peak was. This should make your analyzer display somthing that looks like two mountain tops with a valley where the center frequency of the eq is.
Then start alternately turning back the "Q" and "CUT" controls until you get a smooth response. If the peak was broad, your "Q" will be low. If the peak only affected a couple of bands, the "Q" will be higher.
Like all tuning related items, experience is the key. Futhermore, we all have our own styles for what sounds best and conforms to standards.
It is not unusual for two different EQs to have the same response and sound differently but both be within ANSI/SMPTE 202M. The difference being in the technique in which each was achieved.
Steve
------------------
"Old projectionists never die, they just changeover!"