Water pump and fast water connector for BARCO

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Juan Jose Garcia Calvo
    Film Handler
    • Jan 2020
    • 81
    • Valladolid (Spain)

    #1

    Water pump and fast water connector for BARCO

    Hello.
    Our water pump on our DP3000 is dead. Communicator told "water flow not ok" and lamp didn't start. We had to returm the money to a near full cinema

    Tomorrow we are going to dissasemble the light engine, lamphouse and backpanel card to access to the pump to try to clean it (if this is the problem)

    If this dont work, we can try to make an external water cooling circulation with an temporaly water pump. Anyone know the power of the original pump?
    Original pump I think is 22V, but I don't know the power or the ltrs / min it need.
    I could use the IN and OUT fast connect ports inside the lamphouse holder to make water (glicol, of course) circulating, but I need to know the connector reference or compatible type. Any help?

    Thank you!!!
  • Marco Giustini
    Film God
    • Jan 2020
    • 1191
    • Reading, UK

    #2
    Haven't heard the DP3000 name in quite some time! They were EOL many years ago!

    have you been replacing the coolant periodically? If not, there is a chance your coolant has got gooey and that might prevent the impeller from spinning. If anything has broken, I'd imagine it's the impeller and/or the flow sensor.

    I'd first start with trying to ascertain whether the flow is actually not there - I assume you have some water line connectors so you can open the line and use a container to see if the pump is actually working or not.

    Be careful with those old connectors and coolant lines, if memory serves, the UV in the engine vane would make them brittle.

    Comment

    • Juan Jose Garcia Calvo
      Film Handler
      • Jan 2020
      • 81
      • Valladolid (Spain)

      #3
      Thank you for your advises, Marco.

      We replaced the liquid only one time in 2020, and it was clean (in apperance).

      This projector only make 4 shows a week and 9 months a year, and we use a 3000W xenon lamp (it accepts even 6000 or 6500W), so is not too much. We brought it from Barco as a refurbished projector in 2011.

      The water pump is not working (checked). I hope the flow sensor is ok. If not, I will need to see where is it located and then shotcircuit it. We need to make this projector work again.

      We will take care with the plastic water connectors due the UV exposure, but they seems to be ok.

      In 2020, when we change the glicol, we brought somewhere some water connectors with automatic valve (closed when disconnected) but when we put on the DP3000 connectors, they loose liquid...
      Maybe they are Barco specific connectors or are any standard?

      Thanks again

      Comment

      • Marco Giustini
        Film God
        • Jan 2020
        • 1191
        • Reading, UK

        #4
        It's been a while, I believe Barco had an upgrade kit for those machines. Early connectors were dripping a few drops of coolant by design when disconnected. Later designs were better and you could swap them all with a kit. This might be for early series 2 units though. In fact, I found an old info-T from Barco, 1143, which warns of cracks on earlier Series 2 coolant connectors. They recommend replacing them all every 5 years!

        SCR-20261014-ppec.png

        I've never played around a DP3000 engine, I do not know what material the cooling inlets are made of. Be careful as they might be fragile and I doubt you'll get spares.

        When you say the pump doesn't work, you mean it doesn't spin or there is no flow? How did you check it if you don't mind me asking? If memory serves DP3000s don't have a reservoir so it's a bit tricky to see coolant flowing.

        Comment

        • Juan Jose Garcia Calvo
          Film Handler
          • Jan 2020
          • 81
          • Valladolid (Spain)

          #5
          The pump make no noise, no vabration at all. We tryed expelling the air of the circuit where pump must move the liquid to the outlet (as user manual says), but there was no liquid movement. even if we checked that circuit is full of liquid.

          Bad design of this barco as we need to take out the light engine (disconnecting from the cooling circuit), the back plane card, etc... to acces to the pump.
          I'm worried about taking out the light engine, but as I told you before, we need to make this projector work again.

          Comment

          • Dave Macaulay
            Pro Film Handler
            • Jan 2020
            • 464
            • Toronto, Ontario, Canada

            #6
            If you can get it connected, a simple fountain pump would be fine for flow, but the pump probably has a tach output and the system might refuse to light thinking the pump has stopped.
            Been a while since I worked on a 3000 but recall the cooling system as very problematic. It would love to report "low flow" with no actual problem, just fiddling with it or doing a refill would resolve that for a while.

            Comment

            • Marco Giustini
              Film God
              • Jan 2020
              • 1191
              • Reading, UK

              #7
              I found a DP3000 service manual and yes, it's a pain! I remember pressurising those coolant circuits back then - eventually Barco told us that unless the projector was installed upside down, there was no need for that!

              Indeed if the pump is not vibrating, that might be a big clue. however, make sure you don't have air in the pump. The series 2 design was so much better on that. Do you have the big syringe+piping kit from Barco? Before dismantling the whole thing, I'd follow the process to remove air bubbles and push some coolant in the line, in case the pump got stuck somehow. Yes, you should feel the pump vibrating though...

              Comment

              • Juan Jose Garcia Calvo
                Film Handler
                • Jan 2020
                • 81
                • Valladolid (Spain)

                #8
                Originally posted by Dave Macaulay
                If you can get it connected, a simple fountain pump would be fine for flow, but the pump probably has a tach output and the system might refuse to light thinking the pump has stopped.
                the pump have a simple 3 wire connector, you’re right, but….
                in the pump side of the connector there are 3 wires, but in the projector side of this connector, there are only 2 (both blue wires), so si think there is no tacho connected to the projector.

                Originally posted by Dave Macaulay
                Been a while since I worked on a 3000 but recall the cooling system as very problematic. It would love to report "low flow" with no actual problem, just fiddling with it or doing a refill would resolve that for a while.
                this projector gave sometimes error in the boot, about the flow, but a re-start solved all the times… except this last Sunday…

                we tryed to refill with the syringe but error persist.

                Comment

                • Marco Giustini
                  Film God
                  • Jan 2020
                  • 1191
                  • Reading, UK

                  #9
                  Well the manual itself recommends to open the pump, inspect the impeller and "clean the bearings" so hopefully it's designed to be serviced. Quite a few years ago I disassembled and cleaned a Kinoton pump and I was surprised how well it was built, totally designed to be serviced. I hope you are in luck and can revive the beast.

                  Comment

                  • Pete Naples
                    Pro Film Handler
                    • Jan 2020
                    • 137
                    • Dunfermline, Scotland

                    #10
                    Originally posted by Marco Giustini
                    Well the manual itself recommends to open the pump, inspect the impeller and "clean the bearings" so hopefully it's designed to be serviced. Quite a few years ago I disassembled and cleaned a Kinoton pump and I was surprised how well it was built, totally designed to be serviced. I hope you are in luck and can revive the beast.
                    The pumps used in Kinotons were from the world of solar panels, you are absolutely right Marco, they were very serviceable. I revived many by stripping down and cleaning.

                    Comment

                    • Leo Enticknap
                      Film God
                      • Jan 2020
                      • 3629
                      • Loma Linda, CA

                      #11
                      Flushing and refilling the Series 1 liquid cooling system really belongs in the "projectionist nightmares" thread.

                      Do Barco Series 1 and Series 2 projectors use the same model of pump? I know that the model of pump supplied for Series 2s changed around 2018 or '19 (from then on, as part of maintenance D, you had to ensure that the firmware was up to date, because using the new model of pump in a projector with older firmware could damage it), and it may be that the newer hardware variant is in some way incompatible with Series 1s. But it might be worth putting the question to Barco. If it is the same, you could order one from them.

                      As for the quick release hose connectors, the connectors for Barco Series 2 projectors are these guys: male / female. Series 1s had a different model and I don't know the OEM info. But the specs of this one claim that it can withstand up to 8.3 bars of pressure. Given that you were supposed to pump up the Series 1s to one bar, I see no reason why these wouldn't work.

                      Comment

                      • Christos Gartaganis
                        Film Handler
                        • Sep 2021
                        • 58
                        • Athens Greece

                        #12
                        The hose connectors in Series 1 projectors are also made by CPC, but they are different from those used in S2 projectors.

                        Comment

                        Working...